Wiring Diagram ec-256

txjutsutxjutsu
Updated
    txjutsu

    If anyone can help I need a wiring diagram for the EC-256.. 2 vol 1 tone/push pull.. Bought this guitar used and someone did some "modifications"... thanx in advance..

    Dislike (0)
      Share
    Matt C.
    Matt C. wrote

    Same here man. Can't find a damn thing about it. Might have to replace the lot. 

    Reply
    Dislike (0)
      OneMileLost
      OneMileLost wrote

      Why can't you just use the diagrams from the Seymour Duncan or DiMarzio page? Or any diagram for 2 vol 1 tone/push pull? 

       

      Reply
      Dislike (0)
        jake s.
        jake s. wrote

        Speaking of the ec-256, i found a satin black on that has faded paint. Anything special about them?

        Reply
        Dislike (0)
          Kevin B.
          Kevin B. wrote

          I can't get the Diagrams to upload on this forum.

          Reply
          Dislike (0)
            Kevin B.
            Kevin B. wrote

            Reply
            Dislike (0)
              Kevin B.
              Kevin B. wrote

              Just installed these Duncan's Hot Rodded Humbuckers last night

              Reply
              Dislike (0)
                Kevin B.
                Kevin B. wrote

                Please note, on the wiring Diagrams, that different brand Pickups have different color codes, 

                G&B - Black is the same as Green on the Duncan

                G&B- Green is the same as Red on the Duncan

                G&B- Red is the same as Black on the Duncan

                White is the same as White

                Bare is the same as Bare

                 

                Reply
                Dislike (0)
                  Mr.White
                  Mr.White wrote

                  Kevin B. I realize I'm a bit late to the party on this topic, but just curious, do I need to order the 4 conductor versions of the duncans if I'm going to replace the stock pickups? 

                  I'm wanting to still use the coil split on the tone knob.

                  Thanks for posting the wiring diags as well.

                  Dislike (0)
                    load more replies (2 of 2)
                    William M.
                    William M. wrote

                    Anybody have a wiring diagram for the 3 way toggle switch?

                     I tried to upgrade to a switchcraft using the same wiring but apparently the switchcraft is very different 

                    thanks

                    Reply
                    Dislike (0)
                      Lt M.
                      Lt M. wrote

                      I have as old an EC256 SOLID mahogany as you can get!! Best intonation and setup..upgraded all hardware..?is the a diagram for a harness that would use a Seymour Duncan blackout module as master tone and 2 volumes...upgraded as possible...many thx

                      Reply
                      Dislike (0)
                        Lt M.
                        Lt M. wrote

                        Ps using vintage DiMarzio Steve Morse sig 2 wire humbuckers braided cover ground. , Cloth covered why hot..?again thx

                        Reply
                        Dislike (0)
                          kevin s.
                          kevin s. wrote

                          i am electrician from Canada and very well know about wiring diagram. I usually upload all solution on my blog CapCut Template . Hope you guys will appreciate it.

                          Reply
                          Dislike (0)
                            Koni P.
                            Koni P. wrote

                            Yes, You are right

                            Reply
                            Dislike (0)
                              Eric P.
                              Eric P. wrote

                              I bought one of these as a fixer upper to work on fret dressing. Damn thing was already legit, highly disappointed, lol. 

                              Reply
                              Dislike (0)
                                peter l.
                                peter l. wrote

                                wiring diagram is helpful is making connection

                                Reply
                                Dislike (0)
                                  peter l.
                                  peter l. wrote

                                  Hey there,

                                  I'm in a bit of a pickle with my EC-256 guitar. I got it secondhand, and it looks like the previous owner tinkered with the wiring. I'm on the hunt for a wiring diagram specifically for the EC-256 model, complete with 2 volume knobs, 1 tone knob, and a push-pull switch. If anyone's got a detailed diagram, visits Capcut Templates, and can  point me in the right direction, I'd be super grateful. Huge thanks in advance for any help you can offer!

                                  Cheers, [peter]

                                  Reply
                                  Dislike (0)
                                    Post to Thread

                                    Cancel